Clear Table Top Epoxy

https://www.epoxy.com/epoxy-tabletop-resin.aspx[11/2/2022 6:35:43 PM]

Home Product Catalog About Us Adhesives Chemical Resistant Epoxy Coatings

Flooring Installation Joints Mortars & Grouts Primers & Sealers Specifier's Info

Structural Waterproofing MSDS &Tech Data Ordering Info

The Right Product for the Right Job Since 1980

[Contact Us]

Epoxy Tabletop Resin - Epoxy Bar Top Resin

Water Clear Epoxy Casting Resin

Product #214

Table Top Resin Description

Product #214 Water Clear Epoxy Casting - Tabletop Resin - Bar Top Resin is an all-purpose, low

viscosity epoxy resin system for coating wood and concrete counter tops, tabletops, bar tops and similar

applications.

Product #214 Water Clear Casting-Tabletop-Epoxy Bar Top Resin is commonly used as a clear self-

leveling flooring material, where an extremely flat and level floor is required over concrete and wood.

Product #214 Casting-Epoxy Tabletop-Epoxy Bar Top Resin is used extensively for ultra flat leveling of

surfaces under equipment, where a very strong ultra flat bearing surface is a must. It is also used

successfully for ultra flat floors for stages, dance floor, and clean rooms.

Product #214 Clear Casting-Tabletop-Bar Top Resin is used as a clear adhesive matrix for specialty

colored glass and colored aggregate flooring and tiles. Product #214 Clear Casting-Clear Tabletop Resin -

Clear Bar Top Resin forms a glossy, hard surface, which is resistant to stains. It is also used extensively as a

water clear casting resin.

Product #214 Clear Casting- Clear Tabletop- Clear Bar Top Resin has excellent clarity and color

Clear Table Top Epoxy

https://www.epoxy.com/epoxy-tabletop-resin.aspx[11/2/2022 6:35:43 PM]

retention. Product #214 Clear Casting Resin-Tabletop Resin-Bar Top Resin has zero (0) VOC making it

essentially odorless and can therefore be used in occupied areas.

Advantages of Clear Table Top Resin #214

Low odor for use in occupied areas

Low viscosity - good wetting properties

Meets USDA standards for use in food handling applications

Glossy finish

Stain resistant

Zero (0) VOC - No VOC means it meets the toughest low VOC standards.

Consideration When Using Clear Table Top Resin

Minimum application temperature of Product #214 Clear Epoxy Casting-Tabletop-Bar Top Resin is

50° F.

Substrate to receive Product #214 Water Clear Resin must be free of curing agents and any foreign

materials.

Surface Preparation of Table Top Epoxy

Surface Preparation is the most critical portion to any successful epoxy application. All substrates to receive

Product #214 Water Clear Casting-Tabletop-Bar Top Resin must be properly cleaned and prepared.

Substrate must be free of oil, paint, sealer, caulking, and all other contamination that will interfere with the

bonding of this material. Please see Surface Preparation. Contact us for more details.

Mixing Instructions for Clear Resin #214

Stir each component separately. Combine 2 parts A to one part B by volume into a clean container. Stir for

three minutes, with an Mixing Paddle, scrapping bottom and sides of container frequently. Do not add

thinners.

APPLICATION PROPERTIES @77°F

Mix Ratio 2:1 By Volume

Viscosity (mixed) 950 CPS

Pot Life (200 gr.) 30-40 minutes @ 70° F.

VOC 0

Cure Time (recoat) 10-14 Hours

Ultimate cure @ 74 Degrees F. 5 days

Color Clear

Packaging Unit Size 3 gallon units

Clear Table Top Epoxy

https://www.epoxy.com/epoxy-tabletop-resin.aspx[11/2/2022 6:35:43 PM]

Performance Properties

Tensile Strength ASTM D-638 8500 psi

Elongation ASTM D-638 5.5%

Adhesion to metal 2500 psi

Adhesion to concrete ACI

Committee 403

350 psi (Concrete fails)

Hardness ASTM D-2240 80 (Shore D)

Abrasion Resistance ASTM C-501 35-40 mg loss (CS-17 wheel, 1kg load, 1000

Cycles)

Service Temperature MIL-D-

3134F

160 F (Immersion)

185 F (Dry Heat)

Impact Resistance MTI-D-3134F§

4.7.3

Withstands 16ft/lbs no cracking,

delamination or Chipping.

Indention MIL-D-3134F §4.7.4 Withstands 2000 lbs./sq. in. for 30

minutes without indentation

Elevated Temperature Resistance

MIL-D-3134F § 4.7.5

No slip or flow at required temperatures at

158 F.

Water Absorption ASTM D-570-

(24 hour immersion)

0.10% maximum

Flexural Strength ASTM D-790 8000 psi

Compressive Strength ASTM D-

695

11000 psi

Application of Table Top / Bar Top Epoxy

Application of Product #214 Water Clear Resin will vary with application method. Be careful not to

incorporate bubbles into the coating. Typical pours are in the 1/16 inch to 1/2 inch thick range per coat. If a

second coat is desired, remove all dust, if more than 24 hours after the last coat lightly sand, and then apply

second coat.

Safety Precautions When Using Epoxy

Keep away from children. Refer to the Material Safety Data Sheets (MSDS forms) pertaining to this product

before using. Avoid contact with skin or eyes. Prolonged or repeated exposure may cause eye and skin

irritation. If skin contact occurs, wash immediately with soap and water. If contact with eyes occurs, flush

eyes as required with clean water and seek medical help. Use safety glasses with side shields and wear

protective rubber gloves.

Cleaning up Epoxy Tabletop - Bar Top Resin

Remove Product #214 Water Clear Resin from all tools and equipment before the system gels. Use MEK,

Acetone, or any lacquer solvent.

Chemical Resistance of #214 Bar Top Resin

Clear Table Top Epoxy

https://www.epoxy.com/epoxy-tabletop-resin.aspx[11/2/2022 6:35:43 PM]

Acetic Acid 5% L Lactic Acid- 15% R

Acetone L Methyl Ethyl Ketone L

Methyl Ethyl Ketone L Nitric Acid 10% R

Bleach L Sodium Hydroxide 50% R

Citric Acid 30% R Skydrol R

Crude Oil & Diesel Fuel R Sulfuric Acid 20% R

Ethylene Glycol R Toluene R

Fatty Acids L Urea R

Gasoline R Vinegar L

Hydrochloric Acid 15% R Xylene R

R=Recommended for continuous service L=Limited recommendation, occasional spills.

Coverage: 231 cubic inches per gallon. At 1/8 inch thick 12.8 SF Per gallon.

Use the Top Resin Calculator

to double check your estimate.

More Information

Information on using Table Top Resin in a River Simulation.

Proper mixing and installation is critical to the optimal success of all products. See Installation Tips,

Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or

concerns that you have.

For more information please contact:

Epoxy.com

A Division of Epoxy Systems, Inc

A Vermont Corporation

USA

We have products that have passed the test of time as

well as the best new Systems

available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM

321-206-1833 Customer Service - Ordering and Order Status

Katey Lambert-Fontaine, VP - Chief Operations Officer

[email protected]

Technical Support

Clear Table Top Epoxy

https://www.epoxy.com/epoxy-tabletop-resin.aspx[11/2/2022 6:35:43 PM]

Home Sales Terms MSDS &Tech Data Online Ordering Authorization Form

Add this page to Favorites

352-533-2167 Norm Lambert, President - Technical Support Director

[email protected]

352-489-1666 Accounting and Administration

Debby Lambert, CEO, and CFO Debby Lambert, CEO, and CFO

352-489-1625 Fax line to all Departments

for over 25 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All

rights reserved.

We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Secure